Skip to content

Wearable Mesh Rider Radio – 2400~2482 MHz (WiFi Band)


The Wearable Mesh Rider Radio brings private wireless networking and dynamic mesh capabilities to connected workers. Each device is a node on a long-range Mesh Rider network and uses WiFi to bridge Tablets and Smartphones onto the network. The Wearable Mesh Rider Radio is used by tactical teams to collaborate by streaming voice, video, and data on a fast, low latency, and encrypted network.

The Wearable Mesh Rider Radio was designed to be conveniently carried. Embedded antennas are capable of streaming HD video to a teammate up to 1 km away. External antenna ports are included to integrate with high-gain antennas for longer distances. The radio can be powered by a variety of sources, including tablets and standards-based battery banks. It is also available in an OEM form factor for embedded use cases.

As with all Mesh Rider Radio form factors, the Wearable is available in many frequency bands between 900 MHz and 6 GHz freq range. This flexibility allows customers to use their industry specific frequency bands for deploying private wireless networks.

The Mesh Rider Radio employs Doodle Labs' patented Mesh Rider® technology with state-of-the-art RF and networking capabilities that enable communication further, faster, and more reliably than any comparable solution on the market. For example, optimized video streaming carries crystal clear 4K video while simultaneously carrying Ultra Reliable Low Latency (URLLC) command and control (C&C) data for machines.

For more information, please visit:

Key Features - Mesh Rider Radio Platform


  • Long range (field tested >100km) and high throughput (up to 100 Mbps) Mesh Rider waveform
  • Interference resistant COFDM for robust link quality in difficult RF environments
  • Exceptional Multipath and NrLOS MIMO performance
  • Adaptive radio modulations from BPSK up to 64QAM, with fast per packet optimization to maximize link performance in dynamic environments
  • Software defined channel bandwidth for efficient re-use of spectrum
  • Convolutional coding, Forward Error Correction (FEC), ACK-retransmits, Maximal Ratio Combining, Spatial Multiplexing, and Space Time Block Coding for robust data transmission over noisy channel/spectrum
  • Single channel, Time Division Duplexing (TDD) for bi-directional traffic
  • Resistant to high-power jamming signals
  • ATPC for widely dispersed mesh network
  • Built-in Spectrum Scanner to help mitigate interference issues

  • Ultra-Reliable Low Latency Channel (URLLC) for Command and Control
  • Optimized video streaming channel for Unicast and Multicast transport
  • Self-healing/self-forming multi-frequency mobile mesh for highly reliable network with redundancy
  • FIPS Certified AES 256- and 128-bit encryption
  • End-to-end IP architecture with Ad Hoc, WDS transparent bridge, Client, AP, and Internet Gateway operating modes
  • Embedded network management APIs

  • Very small size, weight, and power for mobile applications
  • Ethernet, USB, and UART interfaces to allow easy integration into different system architectures
  • Leverage the benefits of the most extensible OpenWrt ecosystem and install 3rd party IoT applications
  • Rugged, vibration resistant construction to meet MIL-specs
  • MIL-spec temp range (-40C to +85C)
  • High quality, manufactured in ISO 9001 and ISO 14001 certified facilities
  • COTS – Commercial off the Shelf
  • Extended lifespan and availability
  • System Integration

    The Mesh Rider Radio has been designed to be plug and play. Only USB and a power supply are required for integration.

    Visit Doodle Labs Technical Library for extensive design-in documents.

    Technical Specifications (2400~2482 MHz, WiFi band)

    Model Category XTreme
    Radio Configuration 2x2 MIMO
    Model # (Wearable) RM-2450-2K-XW
    RM-2450-2K-XWE (does not include internal Mesh Rider antennas, Altimeter and GPS functionalities)
    RM-2450-2K-XWE-C (does not include internal Mesh Rider antennas, Altimeter and GPS functionalities)
    Model # (OEM) RM-2450-2K-XO
    Evaluation Kit (Optional) EK-2450-2K Includes: 2x Attached Antennas for Mesh Rider, Breakout board, Cable, Mounting plate
    Design-In Documentation Doodle Labs Technical Library
    Data Throughput at 10-meter range with Attached 3 dBi Antennas (Indicative) 80 Mbps (20 MHz Channel)
    40 Mbps (10 MHz Channel)
    20 Mbps (5 MHz Channel)
    12 Mbps (3 MHz Channel)
    Over the Air Data Encryption 128-bit AES (Full throughput)
    256-bit AES (12 Mbps max throughput)
    FIPS Certification (Optional) FIPS 140-3
    Operating Modes WiFi Radio: AP, Client
    Mesh, WDS AP, WDS Client
    Bridged or Internet Gateway with NAT
    Command & Control channel Ultra-Reliable Low Latency Channel (URLLC). Latency 1.5-10 ms
    Video Channel Optimized video streaming with Unicast and Multicast transmission
    Protocol Compatibility Fully compatible with Doodle Labs Mesh Rider Waveform
    Frequency Range 2400-2482 MHz
    Advanced Band Filters Dedicated SAW filters for high interference immunity
    Max RF Power at SMA port (Software control)
    Each radio individually calibrated
    1.0W (30 dBm) @ MCS 0,8
    0.8W (29 dBm) @ MCS 3,11
    0.4W (26 dBm) @ MCS 5,13
    250mW (24 dBm) @MCS 7,15
    Channel Sizes
    (Software Selectable)
    3, 5, 10, 20 MHz
    Radio Data Rate Auto adapting Modulation Coding Scheme (MCS0-15)
    Antenna Signal Strength -25 to -85 dBm (Recommended), Absolute Maximum= +12 dBm
    RF Power Control In 1 dBm steps, Tolerance ±1 dBm
    Automatic Transmit Power Control (ATPC) Intelligently adjusts the transmit power for very close range operation
    Integrated Antenna Port Protection Able to withstand open port, >10 KV (contact) and >15KV (open air discharge) as per IEC-61000-4-2
    Wireless Error Correction FEC, ARQ
    Receive Noise Figure +4 dB
    Receive Adjacent Channel Rejection (ACRR) 34 dB @ MCS0 for 20 MHz channel (Typ)
    Transmitter Adjacent Channel Leakage Ratio (ACLR) < 28 dBr (Fc ± ChBW)
    Transmitter Spurious Emission Suppression < 40 dBc
    Frequency Accuracy ±10 ppm max over life
    WiFi Standard IEEE 802.11n, 2x2 MIMO
    Frequency Range 2400-2482 MHz
    5160-5895 MHz
    RF Power Output (Typ) 50 mW (17 dBm) EIRP
    Channel Size 20 MHz
    Radio Data Rate Auto adapting Modulation Coding Scheme (MCS 0-15)
    Antenna Signal Strength -25 to -85 dBm (Recommended), Absolute Maximum= +12 dBm
    RF Power Control In 1 dBm steps, Tolerance ±1 dBm
    Wireless Error Correction FEC, ARQ
    Mesh Router Self-Forming/Self-Healing, Peer to Peer
    Custom Software Package Manager Image Builder, OPKG, ipk
    Radio Management Web GUI (HTTPs), SSH and JSON-RPC
    Access control Password, MAC, IP, Port filtering
    Supported Protocols IPv6, QoS, DNS, HTTPS, IP, ICMP, NTP, DHCP
    Software Upgrade Over the air software upgrade supported
    Power Input 6V - 24V, USB-PD Compliant
    DC Power Consumption 14W @ Max Data Troughput
    12W @ Max Range
    3.5W in Rx mode
    2W in Standby mode
    Dimensions: Wearable 130 x 75 x 23 mm and 245 grams
    Dimensions: OEM 127 x 63 x 13 mm and 125 grams
    Mesh Rider Antenna Ports 2x Embedded Antennas and 2x SMA-Female connectors for Attached/External antennas
    Host Interface USB-Dev, Ethernet (100 Base-T), 1x UART (3.3V), USB-Host, and 1x GPIO port (2.62V)
    Temperature range (Operating) External Temp: Up to +40°C (Wearable)

    Industrial: -40°C to +85°C
    Commercial Operating Temp Range: -10°C to +65°C

    * System's thermal design should ensure that the radio's case temperature is maintained within these specifications.
    Temperature range (Non-Operating) -40°C to +100°C
    Ingress Protection IP51, protected against dust and rainfall
    Relative Humidity 5% to 95% non-condensing
    Shock and Vibration Resistance Compliant to MIL-STD-810H for high shock and vibration
    Reliability Extreme Reliability, IPC Class 2 standard with Class 3 options
    WiFi Hotspot Antennas 2x Embedded Antennas
    GPS Features Simultaneous multiple constellations (GPS/SBAS/Galileo/Glonass/BeiDou/QZSS)

    Receive Sensitivity -167 dBm, Max. Velocity 500m/sec ± 0.05m/S, Heading ± 0.3 degrees, Position Accuracy 2m
    Integrated GPS Module with LNA u-blox MAX-M8 series Concurrent GNSS Module (
    GPS Antenna Embedded Antenna
    + SMA-Female connector for external Passive antenna (use of Active GPS antenna is not recommended)
    Integrated Altimeter -698 to +11,775 m (20-bit), 1 Hz Refresh Rate. MPL3115A2
    Integrated Temp Monitor -40 to +85 C MPL3115A2
    Integrated CPU MIPS 24Kc, 540 MHz, 32MB Flash, 64MB DDR2 RAM
    ESD Protection IEC 61000-4-2 test criteria, Level 3 (±6KV) for Contact Discharge and Level 4 (±15KV) for Air Discharge
    MTBF >235k hours (25 years)
    Life Cycle Planning Extended lifespan with 7 years guaranteed availability
    J/F-12 Certification J/F # 11929 (NTIA DD1494 available upon request)
    Regulatory Requirements Designed and verified to meet various regulatory requirements. Formal testing and approval are required for the Integrator's antenna type. The Integrator is responsible for obtaining all regulatory approvals in target markets for the finished product.
    RoHS/WEEE Compliance Yes. 100% Recyclable/Biodegradable packaging
    ECCN Code 5A992
    HS Code 85256010
    MCS RateModulationCombined Output Power (dBm)Sensitivity (dBm)UDP Throughput (Mbps)
    0BPSK (1/2)30-935.4
    1QPSK (1/2)29-9110.62
    2QPSK (3/4)29-8915.66
    316-QAM (1/2)29-8720.52
    416-QAM (3/4)28-8329.88
    564-QAM (2/3)27-7938.88
    664-QAM (3/4)26-7743.11
    764-QAM (5/6)24-7547.34
    8BPSK (1/2)30-9010.53
    9QPSK (1/2)29-8820.43
    10QPSK (3/4)29-8629.7
    1116-QAM (1/2)29-8438.52
    1216-QAM (3/4)28-8054.72
    1364-QAM (2/3)27-7669.3
    1464-QAM (3/4)26-7476.14
    1564-QAM (5/6)24-7282.8

    Note 1: Performance based on 20-MHz bandwidth
    Note 2: Sensitivity and throughput are approximately proportional to bandwidth.